ARM VERSION 1.2 Guide de l'utilisateur Page 117
- Page / 133
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7.7 Tightly coupled memory
Use normal memory access instructions to access TCM. The address is the only difference between an instruction to
access TCM and an access to off-chip memory.
Some cores, ARM966E-S for example, have TCM and no cache.
Other cores, ARM946E-S for example, have both TCM and caches. TCM and caches can be enabled at the same
time, but in general must not map the same regions of physical memory.
Some details of ARM966E-S are described below. Details for other cores vary. For additional information see the
Technical Reference Manual for your processor.
7.7.1 ARM966E-S memory map
Figure 7-3 shows an example of a memory map of an ARM966E-S.
Figure 7-3 ARM966E-S memory map
Multiply aliased memory
The ARM966E-S has up to 64MB of instruction memory, and up to 64 MB of data memory, in TCM.
In the example shown in Figure 7-3, the implementation only has 64KB of instruction memory in TCM. This memory
can be addressed at 1024 different locations, and the TCM ignores bits [25:16] for instruction fetches.
The implementation also has only 32KB of data memory in TCM. This memory can be addressed at 2048 different
locations, and the TCM ignores bits [25:15] for data accesses.
Instruction and data memory
The instruction and data TCMs have independent enables.
When a TCM is disabled, all accesses to its address range result in off-chip access. Off-chip memory and TCM at
the same address are completely independent.
Data accesses to instruction TCM are allowed. This is necessary to allow you to:
Caches and Tightly Coupled Memories
Copyright ?1999 2001 ARM Limited 7-12
- ARM® Developer Suite 1
- Version 1.2 1
- Developer Guide 1
- About this book 2
- ARM publications 3
- Other publications 3
- Feedback 4
- 1 Introduction 5
- Introduction 6
- 1.3 Developing for the ARM 7
- 1.3.5 Writing Code for ROM 8
- 2.1.1 ATPCS variants 9
- 2.1.2 ARM C libraries 9
- • Read-only memory 10
- 2.2 Register roles and names 11
- 2.3 The stack 12
- 2.4 Parameter passing 14
- 2.5 Stack limit checking 15
- 2.6.2 Writing code for ROPI 17
- 2.7.1 Reentrant routines 18
- 2.9 Floating-point options 20
- 3 Interworking ARM and Thumb 22
- 3.1 About interworking 22
- Interworking ARM and Thumb 23
- 3.2.3 Example ARM header 24
- Building the example 25
- 3.2.4 ARM architecture v5T 25
- 3.2.5 Labels in Thumb code 26
- C interworking example 27
- 5. Type go to run the code 31
- String copying example 33
- Operand expressions 33
- Physical registers 33
- 4.1.4 Usage 35
- 4.1.5 Examples 36
- Dot product 37
- Long multiplies 37
- • LDRB/STRB for char 39
- • LDR/STR for int 39
- C++ calling conventions 42
- C++ data types 42
- Symbol name mangling 43
- 4.4.3 Examples 43
- Calling C from C++ 44
- Calling C++ from C 45
- Handling Processor Exceptions 48
- • the address of the handler 53
- 5.4 SWI handlers 55
- Nested SWIs in C and C++ 57
- 5.5 Interrupt handlers 61
- • Single-channel DMA transfer 63
- • Dual-channel DMA transfer 63
- • Interrupt prioritization 63
- • Context switch 63
- Interrupt prioritization 64
- Context switch 65
- 5.6 Reset handlers 67
- 5.8 Prefetch Abort handler 69
- 5.9 Data Abort handler 70
- • A single extended handler 71
- • Several chained handlers 71
- Handling the exception 72
- 5.11.2 The return address 72
- FIQ and IRQ handlers 73
- Prefetch Abort handlers 73
- Data Abort handlers 73
- 5.12 System mode 75
- 6 Writing Code for ROM 76
- 6.2.1 ROM at 0x0 77
- 6.2.2 RAM at 0x0 77
- Implementing RAM at 0x0 77
- System decoder 78
- 6.3 Initializing the system 79
- 6.4.1 Memory map 81
- 6.4.2 Sample code 82
- • five execution regions: 83
- 6.5.3 Sample code 84
- 6.5.4 Building the example 88
- Using the CodeWarrior IDE 89
- Using the command line 89
- 6.6.1 Memory map 90
- 6.6.3 Initialization code 91
- 6.6.4 Building the example 91
- 6.7.1 Memory map 93
- 6.7.2 Building the example 93
- 6.7.3 Sample code 93
- 6.8.1 Memory map 97
- 6.8.2 Building the example 97
- 6.8.4 Sample code 98
- 6.9.2 Using unions 100
- Using an array of shorts 100
- Using a struct 100
- 6.9.4 Using scatter loading 101
- 6.9.5 Code efficiency 102
- 6.10 Troubleshooting 103
- Writing Code for ROM 104
- Code (or read-only) segments 105
- Data (or read-write) segments 105
- Debug data 105
- 7.1.1 About caches 106
- ARMulator Pagetable model 106
- 7.1.4 Cache performance 107
- 7.3 Memory protection units 109
- 7.4 Configuring a PU 110
- 7.5 Memory management units 113
- 7.6 Configuring an MMU 115
- 7.7 Tightly coupled memory 117
- 7.7.3 ARM966E-S warm reset 118
- Debug Communications Channel 120
- 8.4 Target transfer of data 123
- • Using armsd 125
- • Using AXD 125
- Issuing commands 126
- Using AXD 126
- 8.7 Access from Thumb state 129
- 8.8 Semihosting 130
- Glossary 131
© 2020, manymanuals.fr. Tous droits réservés | 0.342 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels